Fatal Error: One or more table pointers are invalid. Modification could be unsafe.

Discussion in 'Windows 7' started by sportysteve555, Sep 23, 2012.

  1. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    So I was upgrading an older computer to Windows 7 Ultimate. Everything went fine, I used Windows 7 Loader by Daz ( Awesome by the way have used before) I did it said it was all good. Restarted. Then went to check and still have the windows needs to be actived within 30 days. So I ran the loader again the computer restarted by itself this time and now I cannot load windows at all. I cant start in safemode, I cant reinstall windows. It will start to then get to the windows screen then just restart itself. I have no idea what to do now because I cant even reinstall windows.... HELP!!!
     
  2. anarchist9027

    anarchist9027 MDL Expert

    Oct 30, 2010
    1,320
    667
    60
    #2 anarchist9027, Sep 23, 2012
    Last edited by a moderator: Apr 20, 2017
    Try this straight from the readme:

    Code:
    1   -   Recovery
    
    Is Windows failing to boot after you installed the loader? Just do the following.
    
    
    * Boot up the PC from your Windows installation disk
    * Press and hold SHIFT and then press F10
    * Input "bootsect.exe /nt60 SYS /force" (without quotes)
    * Restart the PC
    
    
    Note: If the above doesn't fix your boot issue then use the command "bootsect.exe /nt60 ALL /force" instead. Just make sure you remove all USB flash drives before you use the command.
    
    
    
     
  3. Tito

    Tito Super Mod / Adviser
    Staff Member

    Nov 30, 2009
    18,682
    18,581
    340
    Hmm, recover using the method said above. Then re-install the loader with legacy mode checked.
     
  4. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    Cant get to a screen to do that, When I try to hold shift F10 it goes through the loading windows files then it restarts itself
     
  5. anarchist9027

    anarchist9027 MDL Expert

    Oct 30, 2010
    1,320
    667
    60
    You have to boot to your CD rom or Flash Media through your BIOS
     
  6. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    Yes, I tried, I changed everything to only boot from CD, so it will pop up to press any key to load from CD. so I will it starts to load windows files gets to starting windows and restarts
     
  7. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    Also thank you for helping!
     
  8. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    Am I doing something wrong, I have changed the boot in BIOS to only CDROM save changes it goes to boot up and press any key to boot from CD
     
  9. anarchist9027

    anarchist9027 MDL Expert

    Oct 30, 2010
    1,320
    667
    60
    You are doing it correctly
     
  10. sportysteve555

    sportysteve555 MDL Novice

    Sep 23, 2012
    6
    0
    0
    Ya as soon as it does that goes to load then restarts wont let me get anywhere to do anything
     
  11. anarchist9027

    anarchist9027 MDL Expert

    Oct 30, 2010
    1,320
    667
    60
    I honestly cannot tell you what you're doing wrong o_O
     
  12. PhaseDoubt

    PhaseDoubt MDL Expert

    Dec 24, 2011
    1,443
    275
    60
    #12 PhaseDoubt, Sep 25, 2012
    Last edited: Sep 25, 2012
    Are you certain the CD is bootable? Might want to create a new installation disk (burn at slowest speed) from a newly downloaded and authenticated .iso file.

    If all else fails, try a bootable disk partitioning program to wipe your drive and re-partition it. There are many; I prefer GPartEd booted and run from CD. Then do an OS reinstall with your newly created and verified Windows 7 installation disk.

    At this very early point, you have nothing to lose and everything to gain by going all out and starting over with a new OS installation disk and a freshly wiped and formatted HDD.
     
  13. RAGHEB

    RAGHEB MDL Novice

    Oct 8, 2014
    2
    0
    0
    #13 RAGHEB, Oct 8, 2014
    Last edited by a moderator: Apr 20, 2017
    PLEAS HELP ME
    I use This command
    "bootsect.exe /nt60 ALL /force"
    But i used win7 from USB not DVD-ROM
    and my USB flash drive was connected ...
    now my usb prots is not working :(
    What can I do ??
     
  14. zahnoo

    zahnoo MDL Senior Member

    Feb 2, 2011
    387
    35
    10
    You might be better served by asking this in the Windows Loader sub-forum.
     
    Stop hovering to collapse... Click to collapse... Hover to expand... Click to expand...