All SLICs 2.x (Modded Bios List) - Note: For requests use 'Bios Mod Requests' section

Discussion in 'BIOS Mods' started by Yen, Jul 29, 2009.

Thread Status:
Not open for further replies.
Page 87 of 899
  1. luke

    luke MDL Senior Member

    Jun 22, 2007
    458
    35
    10
    #1721 luke, Nov 1, 2009
    the bios update was ment to fix a few problems with the usb because the board doesnt pick up the G19 on post
     
  2. SH@Man

    SH@Man MDL Novice

    Nov 1, 2009
    4
    0
    0
    #1722 SH@Man, Nov 1, 2009
    Request:

    Manufacturer: Asus
    Model: M3N78 Pro
    Version: 1301
    Bios Type: Award
    SLIC: ASUS 2.1
    Link: asus.com/product.aspx?P_ID=DVvm9CU0G1bCC4gp&templete=2

    ty.
     
  3. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1723 NoJuan999, Nov 1, 2009
    Well, that would be a good reason to update. :)
     
  4. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1724 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  5. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1725 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  6. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1726 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  7. SH@Man

    SH@Man MDL Novice

    Nov 1, 2009
    4
    0
    0
    #1727 SH@Man, Nov 1, 2009
    That post can be deleted!
     
  8. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1728 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  9. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1729 NoJuan999, Nov 1, 2009
    Clear CMOS (Remove battery or move jumper), Reset BIOS Options to Default then Exit and Save BIOS Setup.
    Also make sure you do NOT have any loader or Activ*tor on that system.
    And Post Back.
     
  10. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1730 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  11. SH@Man

    SH@Man MDL Novice

    Nov 1, 2009
    4
    0
    0
    #1731 SH@Man, Nov 1, 2009
    Done, reset bios.
    W7 installed today no Actvators was aplied.
    Same problem and now i have a "This copy of Windows is not genuine" in the right corner.
    Any ideas? :)
     
  12. ffcloud2000

    ffcloud2000 MDL Member

    Oct 23, 2009
    164
    5
    10
    #1732 ffcloud2000, Nov 1, 2009
  13. pnasu

    pnasu MDL Novice

    Nov 1, 2009
    11
    1
    0
    #1733 pnasu, Nov 1, 2009
    Last edited by a moderator: Apr 20, 2017
    This worked fine. Although I had a little problem after flashing, where it couldn't find the MAC adress for the onboard netcard, resulting in a message:
    Code:
    Mac address are Invalid in both APC and Flash!
Press F1 to resume
    But after putting a MAC address back on the board with MAC from ASRock it all worked perfectly.
    Did you have any luck making a SLIC2.1 with the 1.80? when i tried it reported a error with the boot block.
     
  14. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1734 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  15. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1735 NoJuan999, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  16. pnasu

    pnasu MDL Novice

    Nov 1, 2009
    11
    1
    0
    #1736 pnasu, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
    I already used it, worked fine. Although i had a little MAC adress problem. Wich could be solved easily. Thanks for the mod.
     
  17. SH@Man

    SH@Man MDL Novice

    Nov 1, 2009
    4
    0
    0
    #1737 SH@Man, Nov 1, 2009
    Last edited by a moderator: May 23, 2017
  18. NoJuan999

    NoJuan999 Experienced SLIC Tool Operator

    Jul 31, 2009
    9,917
    1,941
    300
    #1738 NoJuan999, Nov 1, 2009
    You're Welcome. :)
    Thanks for the feedback.

    PS
    I changed my original post to link to the ISA mod.
     
  19. Dimondigital

    Dimondigital MDL Novice

    Oct 6, 2009
    33
    2
    0
    #1739 Dimondigital, Nov 1, 2009
  20. molder

    molder MDL Junior Member

    Oct 22, 2009
    74
    6
    0
    #1740 molder, Nov 1, 2009
Page 87 of 899