Thanks sebus, With your directions I was able to mod my D915GEV with an Asus Slic 2.1 and it activated. It took me a while to find the Intel2Ami tool but its still out there. For some reason the Slp1.0 did not show up in the bios but I was not to concerned about it. budzos
Intel NUC 3217IYE Bios Mod request Many thanks Tito - OA2Intel 7 worked (needed to revert system date back to 2009)!
(I can't repost skysatone's link b/c I have not posted enough, but it's post #878 in this thread in case someone needs it. It's on page 88.) Confiming that OA2Intel007.rar works on Intel DH87RL motherboard (LGA 1150, Haswell, H87 Chipset). Ran it from bootable DOS thumbdrive with no issues after older version of OA2Intel didn't work. Massive thanks to Skysatone!
Hello all, at the moment I have here a PC with a D975XBX Mainboard from a Friend to make a fresh Installation of Win7. I was lucky to find this Thread here, because I have to flash and start from the scrap but was not sure how to do it. I tried first OA2Intel007 in DOS Mode with an Boot Stick with the Dell-Files and Certificate as written before, but I had no luck because W7 was not activated. Made also the Set of new Date from the Files as written and the Bios time.. Then I tried to reflash all with the OA2INTEL and the Dealin Certificate and I had luck! Its activated as an Ultimate Version with the Dell Key! Not sure if I used the right order or way to do this, but thanks for the explanation here in this Forum to help me out, the result is as wanted.
Thanks Mr Tito. This tool worked fine on motherboard Intel D945GNT with out any difficulty. But did not work in Intel server entry board SE7721BA1-E. Any guidence please? Regards
Thank you Sir, Will you kindly read my request post at 906. Is there any separate forum for Intel Server boards? I have also posted a request at Award & AMI Bios mod requests at post No: 46181 to day. Regards
Dear Mr Tito, I tried to update with modded BIOS provided by Mr. thanah2h MDL GURU vide his post 46183 at Awards and AMI Bios mode requests. The update failed with an error "BIOSID's are identical.There is no need to update this BIOS" Flash update was unsuccessful. Later I hav tried to load the BIOS in recovery mode through Floppy Disk and succeeded. Thank you to all the team of experts. Regards
After a few unsuccessful tries, I was finally able to get the OA2Intel007 to work for me with a DG45ID motherboard using version 135 BIOS. Had to set BIOS date back to 2009 for it to work. I used the win version. Thanks
I too want to use the OA2Intel_7 on my i3 intel NUC. Are the windows 7 keys already added to this package or do i go read more and do it manually? Additionally are these newer tools any good? Intel integrator toolkit and OA3 tool? Never used slic before. Many thanks
Good morning all. I have been doing A LOT of research on how to mod BIOS files to get SLIC 2.1 for both physical and virtual computers. I have been successful in modding my own BIOS files for Dell, HP, Lenovo, VMware, Hyper-V, etc. without the need for requesting a mod on this forum. However, I believe this is where my knowledge becomes limited. I have not, for the life of me, been able to get this Intel server board modded. From my research and experience, I have gotten it close but I am unable to get the XSDT and RSDT headers to change (I believe this is the issue). I would like to learn from this experience and not just ask for someone to do the work for me. So, does anyone here have any experience in this or can you point me in the right direction? Below are the settings that were used in Phoenix/Dell/EFI SLIC Mod v2.18 tool and SLIC ToolKit screenshot of the mod currently applied. View attachment 23725 View attachment 23726 Below is a list of all the information typically requested when doing a mod: Manufacturer: Intel Model: S1200BTL BIOS Revision: 41 BIOS Type: EFI BIOS Download Link: h**ps://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22574&lang=eng&OSVersion=OS%20Independent&DownloadType=Firmware RW Everything Report: h**ps://app.box.com/s/sltttczjp71juibvaga3 If there is any other information you may need, please let me know. I would like to keep this public as much as possible so that others may benefit from it too. Thank you, Mike
You need to manually edit the RSDT & XSDT entries using a hex editor. Search in the DUMP folder to find the respective modules.
-Manufacturer: INTEL -Motherboard Model: DX58SO2 -Bios revision: 0920 -Bios Type: PHOENIX BIOS -Bios Download Link: (Can't link to bios as I'm under 20 posts) Is it possible for someone to modify this bios with SLIC 2.1 (And a SLIC 2.2 version if at all possible too?) I haven't been able to successfully make one.
I have searched thru most of the DUMP files for strings like 'INTELQA09', 'INTEL', 'RSDT' and 'XSDT' but I have been pretty unsuccessful with coming up with anything. Am I simplifying this too much? Is replacing the OEM ID strings as easy as opening a file in a hex editor and changing 'INTEL' to 'DELL'? Why can't I replace the OEM IDs in the RW report? Wouldn't the Phoenix mod tool carry over the changes made manually to the RW report? At this point, I feel pretty lost with this stuff now. I guess once I figure it out It'll be easier the next time.